The Spares Company
Club Shop/Regalia
Parent Website
Contact Officials
Machine Registrar
Club Secretary
Membership Secretaries
MPH Editor and Forum Administrator.
Section Newsletters
Technical Databases
Photos
Home
What's new
Latest activity
Forums
New posts
What's new
New posts
Latest activity
Information
Bike Modifications
Machine Data Services
Manufacturers Manuals
Spare Parts Listings
Technical Diagrams
Whitakerpedia (Vincent Wiki)
The Club
MPH Material Archive
Flogger's Corner
Obituaries
VOC Sections
Local Sections
Local Section Newsletters
Miscellaneous
Club Assets
Club History
Club Rules
Machine Data Services
Meeting Documents
Miscellaneous
Essential Reading
Magazine/Newspaper Articles/Letters
Adverts and Sales Brochures
The Mighty Garage Videos
Bikes For Sale (Spares Company)
Log in
Register
What's new
New posts
Menu
Log in
Register
Install the app
Install
Home
Forums
Forums: Public Access
Tech. Advice: Series 'B' / 'C' 500cc/1000cc Bikes
Main bearing outer race width
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="oexing" data-source="post: 90864" data-attributes="member: 1493"><p>While hoping you don´t burn me on a haystack, would you consider a metric conversion including lipped modern roller bearings that will not walk out in the case like with the factory design - crappy design anyway, but reason was non-availability then. There are some features favourable for these metric types: The o.d is 62 mm , so you don´t weaken the case in this critical place. Just skim the wornout 63,5 mm diameter to accept a sleeve, alu or brass, and get a calculated shrink fit with the new sleeve after pressing in and finish bore so the bearings will let loose at about 120 degrees for future repairs - for other reasons than walked out races. </p><p> I would hate to fit securing screws for the outer race, another weak spot right here. Punch locking the races is a horrible bodge as well, don´t even spend a thought on what that does to the roundness of the race at the punch spots !</p><p> The roller bearing NJ 2206 contains the rollers in the lipped outer race and the inner race has one lip for easy assembling. On the drive side outer bearing I take the type with no lip on the inner race so that slips through both bearings and will position the crank via an axial ring between bearing race and chain sprocket bush, no ball bearing here .</p><p> The timing side has the narrow roller bearing NJ 206, 16 mm wide, and another small NJ , bearing no. 4 . Here is one drawback, the oil pump worm does not slip past the rollers when the bearing already sits in the case. So I will try to thread the case over the crank while the worm lies loosely in the space between inner bearing and the small outer bearing and hope to meet its slot with the woodruff key . If no success after end of patience , no big deal: Heat the case so the big bearing drops out again - thread it onto the mainshaft, the worm onto its place, the small inner race from the timing side outer roller bearing as the last item on the mainshaft - and lastly plunge the enginecase heated over the crank , done. </p><p> I should add, my crank has 30 / 20 mm mainshafts, so for the 1 inch shaft you could simply machine an adapter sleeve for the 30 mm fit. </p><p></p><p> Vic</p><p></p><p>[ATTACH=full]19484[/ATTACH][ATTACH=full]19485[/ATTACH][ATTACH=full]19486[/ATTACH]</p></blockquote><p></p>
[QUOTE="oexing, post: 90864, member: 1493"] While hoping you don´t burn me on a haystack, would you consider a metric conversion including lipped modern roller bearings that will not walk out in the case like with the factory design - crappy design anyway, but reason was non-availability then. There are some features favourable for these metric types: The o.d is 62 mm , so you don´t weaken the case in this critical place. Just skim the wornout 63,5 mm diameter to accept a sleeve, alu or brass, and get a calculated shrink fit with the new sleeve after pressing in and finish bore so the bearings will let loose at about 120 degrees for future repairs - for other reasons than walked out races. I would hate to fit securing screws for the outer race, another weak spot right here. Punch locking the races is a horrible bodge as well, don´t even spend a thought on what that does to the roundness of the race at the punch spots ! The roller bearing NJ 2206 contains the rollers in the lipped outer race and the inner race has one lip for easy assembling. On the drive side outer bearing I take the type with no lip on the inner race so that slips through both bearings and will position the crank via an axial ring between bearing race and chain sprocket bush, no ball bearing here . The timing side has the narrow roller bearing NJ 206, 16 mm wide, and another small NJ , bearing no. 4 . Here is one drawback, the oil pump worm does not slip past the rollers when the bearing already sits in the case. So I will try to thread the case over the crank while the worm lies loosely in the space between inner bearing and the small outer bearing and hope to meet its slot with the woodruff key . If no success after end of patience , no big deal: Heat the case so the big bearing drops out again - thread it onto the mainshaft, the worm onto its place, the small inner race from the timing side outer roller bearing as the last item on the mainshaft - and lastly plunge the enginecase heated over the crank , done. I should add, my crank has 30 / 20 mm mainshafts, so for the 1 inch shaft you could simply machine an adapter sleeve for the 30 mm fit. Vic [ATTACH=full]19484[/ATTACH][ATTACH=full]19485[/ATTACH][ATTACH=full]19486[/ATTACH] [/QUOTE]
Insert quotes…
Verification
What was Mr Vincent's Christian Name?
Post reply
Home
Forums
Forums: Public Access
Tech. Advice: Series 'B' / 'C' 500cc/1000cc Bikes
Main bearing outer race width
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…
Top